XUV835R Premium Cab
Crossover Utility Vehicle
- Premium HVAC cab with light-stone interior
- Cargo box power lift
- LED headlights
- Up to 4,000-lb towing capacity
Starting At:
$32,619.00
View Product Brochure
Features
You will feel confident and comfortable, even on tough terrain, with a full-size Gator™ Utility Vehicle. You will feel stable with a low center of gravity and a wide stance. Engine braking and four-wheel hydraulic disc brakes keep you in control on steep descents, even when fully loaded. The power steering on M- and R-Trim vehicles, is smooth and responsive.
Standard four-wheel drive with rear differential lock
Dash mounted four-wheel drive and rear differential lock switches
With standard four-wheel drive and rear differential lock, both instantly available with the flip of a switch, you can get where you are going.
Dual A-arm front and rear independent suspension
Rear suspension and ground clearance
The independent suspension provides a smooth ride as 203 mm (8 in.) of front suspension travel and 229 mm (9 in.) of rear suspension travel cushions bumps and glides over ruts. And clearing rocks and roots is no problem with 284 mm (11.2 inches) of ground clearance.
Tires for any terrain
Terra Hawk all-terrain tire
Maxxis® Bighorn® 2.0 extreme terrain radial tire
Predator Heavy-Duty all-terrain radial tire
Full-Size Gator Utility Vehicles are available with three tire options:
- Terra Hawk all-terrain tires
- Tread pattern and wide footprint provide excellent traction with minimal impact on terrain
- Maxxis Bighorn 2.0 extreme terrain radial tires
- Radial construction provides shock absorption, allowing for a smoother ride
- Non-directional tread pattern provides predictable cornering and claws up roots and rocks
- Predator Heavy-Duty all-terrain radial tire
- Radial construction provides shock absorption, allowing for a smoother ride
- Flat profile increases footprint area, reducing ground pressure
- 8-ply rating delivers up to three times the life of Bighorn tires
Maxxis® Bighorn® is registered trademark of Cheng Shin Rubber Ind. Co., Ltd.
Full-size Gator™ XUVs are built to work hard and go the extra mile.
Heavy-duty frame
Underside view of XUV865M
Underside view of XUV825M S4
The hefty frame is designed to stand-up to all the bumps and bends of the trail, and the standard front skid plate protects key components from damage.
Constant velocity boot protection
Constant velocity boot protection
Constant velocity joints are enclosed to keep water and dirt out. A protector shield protects the boot from trail debris.
Automotive-grade panels and optional protection packages
TrueTimber® KANATI camo XUV865R with optional Premium Protection Package
The hood and side panels are made of automotive-grade materials that resist scratches and dents, and the cargo box is made of tough composite material that resists dents and rust. Optional protection packages look tough and provide even more protection.
TrueTimber® is a trademark of True Timber Outdoors Holding Company, LLC.
Instrument display, shift lever, and switches (shown on XUV835R Signature Edition)
When you sit behind the wheel of a full-size Gator™ Utility Vehicle, you will be reminded of your favorite pick-up truck. There are controls at your fingertips, an easy-to-read instrument panel, and outlets to recharge your phone.
Shift from park and into gear with a throw of a single lever. Power steering on M- and R- trim vehicles is smooth and responsive.
When the going gets tough, you can instantly engage four-wheel drive and rear differential lock with switches. Even at night, the backlit switches are easy to see. If a front wheel starts to slip, the front differential automatically locks to pull you through.
When you hop into the seat of a full-size Gator™ Utility Vehicle, you will notice there’s seating for you, plus two.
Three-passenger seating with room to spare
40/60 split three-passenger bench seat
Operator platform
The adjustable operator’s seat and tilt steering lets drivers of all sizes get comfortable, and the passenger grab handles help everyone feel secure. The low step height and generous opening between seat base and fender is even designed to accommodate bulky work boots.
Climate-controlled comfort
HVAC controls
Partially-open door windows and fully-open windshield
On cab vehicles, you will enjoy standard heating and air-conditioning that will keep you comfortable in every season, and the tight-closing doors help seal out dust and reduce noise. When you want to let in the breeze, you can also roll down the windows and open the front windshield.
Upgrade to R-trim refinements
Stone colored dash with sport steering wheel
Headliner, sun visors, rearview mirror, and dome light
R-trim vehicles have an upgraded stone-colored cab interior with headliner and rear panel to reduce noise. Standard LED headlights, sun visor, dome light, rearview mirror, and sport steering wheel round out the package.
Stone cloth seat
Stone cloth seat
R-trim vehicles also include a stone cloth seat that keeps cool in the hot sun and warms up quickly in the winter.
XUV835R with AutoTrac Ready option
Interior of XUV835R with Gen 4 4640 Universal Display
Precision ag technologies have changed the way we farm, and John Deere has been at the forefront of that change. Adding the AutoTrac™ assisted steering system and JDLink™ Modem options to Gator Utility Vehicles brings precision ag technology to farms of all sizes.
The AutoTrac Ready option enables hands-free steering through the field decreasing overlap and lowering input costs while reducing operator fatigue. The JDLink Modem option connects your vehicle to the John Deere Operations Center so the vehicle can be managed with the rest of your fleet.
Simplify field boundaries
- Check field boundaries and identify hazards as the Gator Utility Vehicle steers itself along established boundary lines.
- Create new boundary lines, even when the soil is too wet for larger equipment.
Improve soil mapping
- The days of picking a tree across the field to navigate are over. Use guidance lines to create a sampling grid and let your Gator Utility Vehicle keep you on track as you pull plugs across the field.
Connect your Gator Utility Vehicle to the rest of your fleet
- Leave the USB drives at home as you wirelessly send your data to and from your Gator Utility Vehicle.
- A planter operator can flag the exact location of a large rock so the Gator UV can be sent to the location to remove the hazard.
Save time and stop waiting for the perfect day to spray
- When paired with a tow behind sprayer and rate controller, the Gator Utility Vehicle’s lighter weight allows work to be completed when the ground is too wet for larger equipment.
- Speed through spraying by allowing the Gator Utility Vehicle to steer a predefined path around buildings and fence rows.
Track productivity, maintenance, and machine vitals
- Track the current and past locations of your Gator Utility Vehicle in the John Deere Operations Center, just like the rest of your fleet.
- Know when your Gator Utility Vehicle is ready for scheduled maintenance
Share StarFire™ Receiver and Universal Display
- You can leave precision ag technology components installed year-round or share your StarFire Receiver and Universal Display with another piece of equipment.
The full-size Gator™ XUV can haul 454 kg (1000 lb), so load it up with confidence. You can also make fewer trips with 1814 kg (4000 lb) of towing capacity and a standard 51-mm (2-in.) receiver hitch.
Built-tough cargo box
Cargo box (shown with spray-in liner and optional taillight protectors)
Cargo box converted to flatbed
The cargo box resists dents, scratches, and rust because it is made from a tough composite material. You will have no problem securing loads with integrated tie bars and 14 tie-down points. You can also convert the cargo box to a flatbed when you need to haul big and bulky loads.
The cargo box measures 1143 mm (45 in.) long, 1320 mm (52 in.) wide, and 305 mm (12 in.) deep.
One-handed tailgate
Tailgate handle
Since your hands are always full, the tailgate can be opened and closed with one hand. You can also lower the tailgate to carry longer items or remove it for easy cleanout.
Power lift
Deluxe cargo box unloading rocks
To save your back, the optional cargo box power lift empties heavy loads with the push of a button.
812-cc (49.6-cu in.) gasoline engine and drivetrain
The XUV835 and XUV825M S4 Gator™ Utility Vehicles are powered by an electronic fuel injection (EFI) gasoline engine with liquid-cooled, dual-overhead cams. This engine is designed to provide maximum power and fuel efficiency to muscle through tough jobs.
It also has plenty of torque in low range, and fast speeds in high range. The enclosed drivetrain automatically adjusts for fast acceleration, along with powerful hauling and hill-climbing capabilities.
One-row full-size Gator XUVs come packed with places to store tools, gear, and beverages.
Cup holders
Four cup holders and center tray (shown on XUV835E)
Cab door cup holder and pocket
The dash has four cup holders, and cab vehicles have a cup holder in each door.
Dash and under-seat storage
Under seat storage (shown on XUV835E)
Glove box, storage pocket, and two dash bins (shown on XUV835M cab)
The vehicles also feature an enclosed glove box, center tray, dash storage pocket and under-seat storage. Depending on the configuration, vehicles may have up to three additional dash bins and under-hood storage.
Green and yellow XUV835R Signature Edition with included Ultimate Protection Package
Olive and black XUV865M with cab and optional brush guard
TrueTimber® KANATI camo XUV865R with optional Premium Protection Package
Desert sand, XUV835M Honor Edition with included brush guard
You will get noticed with the distinctive styling of full-size Gator™ XUVs. Available in four colors, with various protection packages, and more than 100 attachments, you can create a custom look that will turn heads.
TrueTimber is a trademark of True Timber Outdoors Holding Company, LLC.
Large fuel tank fill opening
Full-size Gator™ XUVs have a large 42.8-L (11.3-gal.) fuel tank so you go further between fill ups. A 76-mm (3-in.) diameter fill opening reduce spills.
Specs & Compare
Key Specs | XUV835R Premium Cab Current Model |
| Engine power | 43* kW 54* hp |
| Cargo box dimensions | 1143 x 304.8 x 1320 mm 45 x 12 x 52 in. |
| Cargo box capacity (weight) | 454 kg 1000 lb |
| Towing capacity | 907 kg 2000 lb |
| Front suspension | Fully independent dual A-Arm with adjustable coils; 7.9 inches (200.7 mm) of travel |
| Rear suspension | Fully independent dual A-Arm with adjustable coils and sway bar; 9.1 inches (231.14 mm) of travel |
| Final drive | Two speed, oil bath |
| Four wheel drive | On-demand true four-wheel drive system |
| Fuel capacity | 42.4 L 11.2 U.S. gal. |
Engine | |
| Type | 4-cycle gas, Electronic Fuel Injection (EFI) |
| Displacement | 812 cc |
| Power | 43* kW 54* hp |
| Cooling system | Liquid |
Drivetrain | |
| Transmission | Continuously Variable Transmission (CVT) with clutch enclosure |
| Final drive | Two speed, oil bath |
| Four wheel drive | On-demand true four-wheel drive system |
| Traction assist | Positive locking, mechanically actuated (hand-operated) |
| Descent control | Yes |
Suspension | |
| Front | Fully independent dual A-Arm with adjustable coils; 7.9 inches (200.7 mm) of travel |
| Rear | Fully independent dual A-Arm with adjustable coils and sway bar; 9.1 inches (231.14 mm) of travel |
Brakes | |
| Type | Front/rear hydraulic disc with twin piston front calipers |
| Park brake | Driveline, internal wet multi-disc, foot operated (hand release) |
Tires / Wheels | |
| Front | 25x9-12 Terrahawk AT, 27x9-R14 Maxxis Big Horn Radials (on Alloy Rims), or Maxxis Big Horn Radials (on Steel Rims) |
| Rear | 25x11-12 Terrahawk AT, 27x11-R14 Maxxis Big Horn Radials (on Alloy Rims), or Maxxis Big Horn Radials (on Steel Rims) |
Dimensions / Capacities | |
| Wheelbase | 2146 mm 84.5 in. |
| Weight | 823 kg 1810 lb With Cab and HVAC: 1019 kg With Cab and HVAC: 2241 lb *Additional Attachments and Accessories will add weight |
| Length | 3228 mm 127 in. |
| Width | 1618 mm 63.7 in. With doors: 1763 mm With doors: 69.4 in. |
| Height | 1981 mm 78 in. With roof: 1987 mm With roof: 78.25 in. |
| Tread centers | Front: 1341 mm Front: 52.8 in. Rear: 1259 mm Rear: 49.6 in. |
| Ground clearance | 284 mm 11.2 in. |
| Fuel capacity | 42.4 L 11.2 U.S. gal. |
| Cargo box dimensions | 1143 x 304.8 x 1320 mm 45 x 12 x 52 in. |
| Cargo box capacity (weight) | 454 kg 1000 lb |
| Payload capacity | 680 kg 1500 lb |
| Towing capacity | 907 kg 2000 lb |
| Hitch | Standard 2-in. receiver |
Features | |
| Color | Green/Yellow, Camouflage, Olive and Black |
| Power steering | No on E Trim; Yes on M and R Trim |
| Battery / Alternator / Power port | 480 CCA 85 amp @ 6000 rpm, regulated, 1020 watts |
| Instrumentation | Digital Display (system diagnostic light, speed, rpm, 4WD indicator, fuel level, coolant temperature, hour meter, miles, park brake light) |
| Storage | Four cup holders (two additional for cab units), in dash, under seat (56.69 L), glove box (3.85 L), optional under hood - except for HVAC units or units with the dealer installed heater kit |
| Seating | Bench (Available Bucket Seats on E and M Trim) |
Additional information | |
| Country of Manufacture | U.S. |
| Date collected |
Offers & Discounts
Accessories & Attachments
Cargo Box
Cargo box pail holder
Cargo box pail holder
The 5-gal. (18.9-L) pail holder is ideal for operators who want to maximize the work capability of their Gator™ Utility Vehicle. The 5-gal. (18.9-L) pail holder keeps pails in place within the cargo box, ensuring that they stay safe and secure. Featuring the quick-clamp mounting system, it mounts easily to the cargo rails of the cargo box with just one clamp.
Cargo bed extender
Cargo bed extender
The cargo bed extender conveniently extends the rear of the cargo bed, and also acts as a cargo box divider when it is flipped inside of the cargo box. The cargo bed extender easily flips in or out with the use of quick-pull pins.
Deluxe cargo box bed mat
The deluxe cargo box bed mat not only protects the steel floor from scratches and dents, it also provides additional cushioning and slip resistance to items being hauled in the cargo box.
Cargo box divider located at rear of cargo bed
Cargo box divider located at front of cargo bed
Speedrail lock in the unlocked position
Speedrail lock in the locked position
The Gator™ XUV Series can be equipped with an optional divider for the deluxe cargo box. The dividers can be positioned at the front or rear of the cargo box bed. To change positions of the dividers, simply release the speedrail locks by hand and slide into new position, then close the locks to secure the dividers.
Cargo box side extension kit
The cargo box side extension kit expands the versatility of the Gator™ Utility Vehicles and is ideal for those who are enhancing their property and landscape. The extensions allow operators to haul twice the volume (not to exceed cargo box weight capacity) of light material such as grass clippings and mulch.
Product features include:
- Four-sided structure that increases cargo box side height to 533 mm (21 in.) and volume to 0.74 m3 (26 cu ft)
- Mounted on the sides and front with hardware, while the tailgate can be attached or removed without tools
- Tailgate pivots at the top (similar to a dump truck) for ease of dumping loose material
- Laser-cut, heavy-gauge, powdered-coated steel provides excellent durability
- Compatible with all model year 2011 to current Gator XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, and M-Gator A2 Utility Vehicles
- Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
- Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles.
- Compatible with Gator cabs and bedliner
NOTE: The cargo box side extensions are not intended to increase the rated cargo box carrying capacity per the vehicle specification.
Rear fender flare kit on XUV865
Rear fender flare kit
A – Fender flare
B – Fender
The rear fender flare kit minimizes debris from reaching the operator station.
Product features include:
- Two pliable fender flares (one for each side)
- Hardware for mounting on the sides
- Compatible with all model year 2011 to current Gator™ XUV825, XUV825 S4, XUV855, XUV855 S4, XUV835, and XUV865 Utility Vehicles
- Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
- Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles
Rear fender flare
Overview
Rear fender flares reduce mud and debris splashing onto the vehicle and passengers. The flares are constructed from a durable molded material and integrated into the cargo box fenders. The attachment kit includes a pair of flares and mounting hardware.
Compatibility
XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, XUV865R vehicles. Signature Edition vehicles include rear fender flares in base equipment.
Tool rack
Tool rack with tools
The side tool rack enables the user to maximize the use of their cargo box by carrying long-handled tools, such as trimmers, shovels, and rakes, on the outside of the box. The holders are adjustable, allowing the users to carry a wide array of items in the racks.
Tool rack holder detail
Adjusting the tool rack holder
Spare tire carrier
Spare tire carrier
Easily mount a spare tire to the side of the cargo box with this convenient kit.
Recommended to carry spare front tire, as the front tire can be mounted on either the front or rear hubs.
Cover
High-performance sport seat cover - black
High-performance sport seat cover - camo
High-performance sport seat cover - coyote
Each kit (available through Order Zone) contains one bench base cover, one backrest cover, and installation instructions.
NOTE: One carton (two kits) outfits driver and passenger seats.
Special features:
- Exceptional abrasion, tear, and puncture resistance
- Constructed with military-grade CORDURA® fabrics
- Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
- Quick and easy installation
- Available in black or Realtree Hardwoods HD® pattern
- Military-grade zippers
- Limited 1-year warranty
- Made in the USA
Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd. CORDURA is a trademark of INVISTA North America, LLC.
High-performance sport seat cover - black
High-performance sport seat cover - camo
High-performance sport seat cover - coyote
Each kit (available through Order Zone) contains one bench base cover, one backrest cover, and installation instructions.
NOTE: One carton (two kits) outfits driver and passenger seats.
Special features:
- Exceptional abrasion, tear, and puncture resistance
- Constructed with military-grade CORDURA® fabrics
- Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
- Quick and easy installation
- Available in black or Realtree Hardwoods HD® pattern
- Military-grade zippers
- Limited 1-year warranty
- Made in the USA
Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd. CORDURA is a trademark of INVISTA North America, LLC.
High-performance sport seat cover - black
High-performance sport seat cover - camo
High-performance sport seat cover - coyote
Each kit (available through Order Zone) contains one bench base cover, one backrest cover, and installation instructions.
NOTE: One carton (two kits) outfits driver and passenger seats.
Special features:
- Exceptional abrasion, tear, and puncture resistance
- Constructed with military-grade CORDURA® fabrics
- Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
- Quick and easy installation
- Available in black or Realtree Hardwoods HD® pattern
- Military-grade zippers
- Limited 1-year warranty
- Made in the USA
Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd. CORDURA is a trademark of INVISTA North America, LLC.
Vehicle storage cover
Vehicle storage cover
Key features
- All-season protection against sun damage, rain, dust, and tree sap
- Reinforced corners for added durability
- Fabric coated for maximum water resistance and repellency
- Elastic shock cord in bottom hem for a quick, custom fit
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Ordering information
Available through Order Zone
Guards
Brush guard
Quick pull pins
Brush guard hinged forward
Auxiliary lights mounted on brush guard (sold separately)
Key features
- Provides a modern and aggressive appearance
- Heavy-duty, 44.45-mm (1.75-in.) diameter, steel tube construction
- Welded steel brush guard provides protection for the front grille, lights, and hood
- Easy-to-use quick pull pins allow the brush guard to be hinged forward to gain access under the hood
- Includes mounts for auxiliary light-emitting diode (LED) lights (sold separately)
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Brush guard extensions
Brush guard extensions
Brush guard with extensions hinged forward
Brush guard with extensions
Key features
- Enhances the aggressive appearance of the vehicle
- Easily attaches to the brush guard (required – sold separately)
- Provides additional protection to the side hood and fender area without adding additional overall width to the vehicle
- Still allows full entry under the hood when brush guard is hinged forward
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Front CV guards
Rear CV guards
Key features
- Kit contains both front and rear CV guards
- Additional added protection for the A-arms and CV joints
- High-strength, formed steel guards handle impacts while maintaining a low, unsprung mass to provide exceptional ride quality
- Easily bolts to the A-arms
- Drainage holes on the bottom of the guards prevent buildup of dirt, grass, and other loose materials
Compatibility
- Model year 2020 and newer XUV835 and XUV865 Utility Vehicles
Front fender guards - shown with brush guard (required) and brush guard extensions (optional)
Key features
- Easily attaches to the brush guard (required – sold separately)
- Provides protection to the front fender area
- NOTE: With fender guards installed, the overall width of the vehicle increases to 1.75 m (69 in.).
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Rear bumper kit (TH 6X4 shown)
The rear bumper offers stylish, heavy-duty rear protection to the vehicle.
Compatible with:
- Model year 2011 and later Gator™ XUV 625i, XUV 825, and XUV 855 Utility Vehicles
- Model year 2010 and later Gator TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
- Model year 2018 and later Gator XUV835 and XUV865 Utility Vehicles
Rear CV guards
CV guards add additional protection for the A-arms, brake lines, and CV half shafts:
- Formed steel guards handle impacts while maintaining a low unsprung mass
- Easily bolt to the A-arms with six bolts
- Drainage holes provided to prevent buildup of dirt, grass, and other loose materials
- Compatible with all model year 2011 to current Gator™ XUV625i, XUV825, XUV855, and M-Gator A2 Utility Vehicles
- Compatible with model year 2013 to current Gator XUV825 S4 and XUV855 S4 Utility Vehicles
- Compatible with model year 2018 to current Gator XUV835 and XUV865 Utility Vehicles
Rear-panel glass protector
Key features
- Provides protection to the cab rear-panel glass
- NOTE: Never carry loads in the cargo box over the load guard.
- Perforated, black metal screen easily attaches to the cab rear panel (required – sold separately)
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Brake and taillight protector
The brake and taillight protector offers increased protection to the taillight assembly from incidental contact.
Harnesses
Dash port harness connection
Dash port harness – lower connectors
Key features
- The front attachment harness (dash port) includes connections for the following kits:
- Rear sprayer
- Rear spreader
- Blades
- GreenStar™ Display as part of the Ag Management Solutions (AMS) integration kit
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Hydraulic blade and rear winch harness
Key features:
- The hydraulic blade and winch harness includes connections for the following kits:
- Hydraulic blade
- Winch
Compatibility:
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Lighting
Beacon light in up position
Beacon light in down position
Backlit beacon light switch
Key features
- 76-mm (3-in.) round, light-emitting diode (LED) strobe light provides excellent visibility for vehicle bystanders
- Especially useful for working around properties and job sites
- Acrylic amber lens resists scratching and scuffing
- Impact-resistant nylon housing
- Society of Automotive Engineers (SAE) J845 (Class 3)-compliant
- UL® recognized
- Flash rate: 60 +/- 10 fpm
- Stands 21.3-cm (8.4-in.) tall from roof/occupant protective structure (OPS)
- Folds down out the way when not in use
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Electrical harness requirements
| XUV835/865 | Attachment harness required (see below) |
| E | 1, 3, 5 |
| M (open station) | 3, 5 |
| M (cab, factory installed) | 5 |
| R | --- |
| 1 | E-spec attachment harness |
| 2 | Front attachment harness |
| 3 | Roof attachments harness |
| 4 | Front cab harness |
| 5 | Rear cab harness |
| 6 | Dash port harness |
UL is a trademark of UL LLC.
Front cab mounted
Rear cab mounted
Brush guard mounted
Key features
- The LED driving lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
- Beam pattern: driving (focused, intense beam of light good for illuminating a stretch of road directly in front of the vehicle)
Driving beam pattern – mounted on brush guard
Driving beam pattern – mounted on OPS/roof
- Lamp sealing: IP69K
- Light output (per light): 1150 lumens
- LED color temperature: 5000 K
- Amp draw (per light): 1.4 amps
- 6 LEDs per light
- Aluminum housing
Compatibility
- Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
- Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
- HPX Utility Vehicles
Front cab mounted
Rear cab mounted
Brush guard mounted
Key features
- The LED work lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
- Beam pattern: flood (spread of light over a wider, shorter distance)
Flood beam pattern – mounted on OPS/roof
- Lamp sealing: IP69K
- Light output (per light): 1200 lumens
- LED color temperature: 5000 K
- Amp draw (per light): 1.4 amps
- 6 LEDs per light
- Aluminum housing
Compatibility
- Model Year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
- Model Year 2018 to current XUV835 and XUV865 Utility Vehicles
- Model Year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
- HPX Utility Vehicles
Operator's Station
Accessory mounting bracket (shown with tablet and cell phone mount)
Key features
- Allows the cell phone and tablet mount to be installed in the upper dash location
- Required for cell phone mount if mounted in the lower dash location
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Cell phones, global positioning system (GPS), and other devices are key tools for farming today. John Deere has now made it easier than ever to incorporate these tools into the operator station.
RAM X-Grip holder
For proper machine operation, it is critical that accessory devices and tools be located and mounted where they are accessible but do not interfere with visibility and controls. The new RAM® mount kit has been specially developed to meet this need in John Deere tractors and now utility vehicles.
Simply remove the large wing nut from the assembly, insert the stud into any open hole in the occupant protective structure (OPS), and tighten down the jam nut.
Key benefits:
- Patented RAM X-Grip™ holder fits most cell phones and similar devices including iPod®, iPad®, iPhone®, BlackBerry®, Samsung Galaxy® and others.
- Mounts to the holes in the OPS
- Ball joints allow for variable positioning
- Holds firm even in rugged terrain
- The holder is compatible with many other RAM® products with their B size or 25.4-mm (1-in.) ball accessories
RAM X-Grip
The RAM X-Grip has a clean and clever four-leg design that sports great holding power without hiding the phone behind foam pads and plastic.
Features:
- Rustproof
- High-strength composite and stainless-steel construction
- Spring-loaded holder expands and contracts for custom fit
- Minimum width: 1.875 in. (47 mm)
- Maximum width: 3.25 in. (82 mm)
- Depth: 0.875 in. (22 mm)
- Rubber-coated tips will hold device firm and stable
- Easy access grip knobs for quick release of your device
Warranty:
90 days, limited.
RAM and RAM X-Grip are trademarks of National Products Inc. iPad, iPod, and iPhone are trademarks of Apple, Inc. BlackBerry is a trademark of Research In Motion Limited (RIM). Samsung Galaxy is a trademark of Samsung Electronics Co.
Tablet mount – upper mount location (shown with cell phone mount – sold separately)
Tablet mount – lower mount location (shown with cell phone mount – sold separately)
Key features
- Keeps tablet at the operator’s fingertips for doing jobs such as soil sampling
- Utilizes a RAM® mount to easily move tablet to desired location
Compatibility
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
RAM is a trademark of National Products, Inc.
Sprayers
45-gal. (170-L) Gator bed sprayer
The 45-gal. (170-L) Gator bed sprayer is designed to work with the Gator vehicles equipped with the steel bed or deluxe cargo box. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 43-in. boom that sprays a 120-in. swath. It's equipped with a 20-ft hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 30 ft. It comes equipped with rubber feet and custom brackets, which secure to the Gator bed, for a no tools mount.
Special features:
- 45-gal. (170-L) capacity
- Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
- Brackets allow boom height adjustment
- 100 psi SHURflo diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage
- The fully adjustable brass spray wand tip achieves streams up to 30 ft
- Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
- Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
- On/off switch located near operator
- Easy boom removal for added convenience
- Control valve channels spray to either the boom or spray wand
- 12-V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
- Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications
45 U.S. gal. (170 L) |
|
Pump |
|
Diaphragm material |
|
| 2.1 U.S. gpm (8 L/min) | |
Remote spray method |
|
Spray wand |
|
Tip material |
|
| Adjustment | Fan-to-stream |
| Hose length | 20-ft nylon reinforced rubber |
Boom |
|
| Boom width | 43-in. (109 cm) fixed |
| Spray swath | 120-in. (305 cm) |
| Spray tip(s) | Three - TF-VP3 |
Mounting |
|
| Steel bed | Custom tailgate clamp mounting |
| Deluxe cargo box | Custom brackets secure to tie-downs |
Compatibility |
|
Ordering information
Contact the local John Deere dealer for availability and pricing information.
45-gal. (170-L) Gator bed sprayer
Order number: LP20852
SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.
High-performance 45-gal. (170-L) Gator bed sprayer
The high-performance Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box or steel bed. With a 45-gal. (170-L) capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and de-icer. Engineered brackets secure the sprayer to the Gator bed with no tools, or additional tie-downs required.
NOTE: Sprayer shown above with optional 150-in. precision boom (LP22885).
High-performance features:
- 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
- Premium pistol grip spray gun, designed for single hand mist to 35-ft stream
- Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
- Glycerin-filled pressure gauge and TeeJet™ pressure regulation/recirculation valve
- Choice of booms (sold separately)
- On/off capabilities in the palm of your hand with the included sprayer remote control (LP22912)
- 12V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
- Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
- Control valve channels spray to either the boom or spray wand
- Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications
Pump |
|
Diaphragm material |
|
| 3.6 U.S. gpm (13.6 L/min) | |
Remote spray method |
|
Spray wand |
|
Tip material |
|
| Adjustment | Fan-to-stream |
| Hose length | 20-ft - 1/2-in. nylon reinforced rubber |
Gauge |
Glycerin filled |
Spray control |
|
Boom (sold separately) |
|
| Option 1 | 150-in. spray width precision folding (5 tip) |
| Option 2 | 120-in. spray width (3 tip) |
| Option 3 | 24-ft boomless nozzle |
Mounting |
|
| Steel bed | Custom tailgate clamp mounting |
| Deluxe cargo box | Custom brackets secure to tie-downs |
Compatibility |
|
Ordering information
Contact the local John Deere dealer for availability and pricing information.
High-performance 45-gal. (170-L) Gator bed sprayer
Order number: LP22908
SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.
340.7-L (90-gal.) single tank sprayer
The high-performance (HP) single-tank 340.7-L (90-gal.) Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box that have a capacity in excess of 362.9 kg (800 lb). The custom molded 340.7-L (90-gal.) tank provides a low profile with capacity perfect for athletic fields, farmettes, commercial maintenance, or any large property. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. Custom engineered mounting hardware ensures the unit stays secure without the use of additional straps or tie-downs. Cover ground quickly with flexible boom options. (Boom sold separately).
High-performance features:
- 100 psi, 4-GPM diaphragm-type pump is designed for high-hour applications and can be run dry without damage
- Premium pistol grip spray gun, designed for single-hand mist to 10.7-m (35-ft) stream.
- Side-mount hose tender for easy hose access and storage
- Glycerin-filled pressure gauge
- TeeJet™ pressure regulation/recirculation valve for precise sprayer calibration
Additional features:
- Custom engineered brackets secure to Gator bed with no tools or additional straps
- Control valve channels spray to either the boom or spray wand
- Includes Gator accessory wiring harness, complete with quick disconnects, for convenient electrical hookup
- Rugged translucent yellow tank with molded fill level indicators (in gallons)
340.7-L (90-gal.) sprayer on XUV835
Overview
The 341-L (90-gal.) rate controlled sprayer for Gator™ utility vehicles is proof that the evolution of modern sprayers is correlated to progress in electronics and forward thinking. By utilizing pulse width modulation (PWM) technology, like the systems found on large-scale ag sprayers, this sprayer provides many of the same features and benefits to operators with XUV835 and XUV865 Full-Size Crossover Utility Vehicles.
Benefits
- Greater productivity due to faster travel while spraying
- Easier adjustments through advanced controls using the 8.1-cm (3.2-in.) display
- Savings on chemical costs thanks to more consistent application rate
- Lower risk of environmental contamination because of precision spray rate
Additional details
With this sprayer, operators effortlessly maintain their application rate without needing to hold a constant ground speed. For example, if the operator slows down to maneuver around an obstacle, the solenoid valves on the sprayer tips compensate by decreasing the rate of material being applied. If the operator stops the vehicle, the solenoid valves shut the tips off completely and the spray returns to the tank through a return valve. This precise measuring of the Gator utility vehicle’s speed is done through a controller area network (CAN) bridge (BUC10316), which provides instantaneous communication between the sprayer and the vehicle.
For simple operation, an 8.1-cm (3.2-in.) display mounts to the vehicle’s dash. This display allows operators to easily select a spray mode (boom or wand), adjust the speed range, tip size, and flow rate, and individually activate or deactivate tips for more application options. After setup, the minimum and maximum speed ranges are shown as a horizontal meter to help the operator avoid traveling too fast or too slow based on their set parameters.
Partnering with this technology is a proven 20-L/min (5.3-gpm) Shurflo® pump that provides up to 4.1 bar (60 psi). Material is applied as wide as 3.8 m (12.5 ft) with a durable, spring-loaded folding steel boom. Also included is a deluxe hand wand with a brass tip that provides both cone and stream spray patterns. Attached to the wand is 9.1 m (30 ft) of hose that is ideal for spot spraying weeds as far 10.7-m (35-ft) away and trees up to 9.1-m (30-ft) high.
Key features
- Rate control technology – allows operators to effortlessly hold their application rate without worrying about maintaining exact ground speed.
- 8.1-cm (3.2-in.) display – provides operators with the ability to select a spray mode (boom or wand), adjustments to the speed range, tip size, and flow rate, and individually activate or deactivate tips for greater application options.
- Pressure control through return valve – helps maintain the droplet size defined by the spray tip, which is important as some materials require different droplet sizes.
- Individual tip shutoff – provides greater options for different spraying applications.
- Shurflo 20-L/min (5.3-gpm) pump – is designed for high-hour commercial applications and provides up to 4.1 bar (60 psi) on demand.
- Spring-loaded, folding steel boom – applies up to 3.8-m (12.5-ft) spray swath. Five XRC TeeJet® nozzles are used to prevent dripping that can lead to spotting.
- Adjustable hand wand – features a brass tip with a spray pattern that can be adjusted from cone to stream, perfect for spraying trees, weeds, and hard-to-reach places.
Compatibility
- Model year 2018 and newer Gator XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Full-Size Crossover Utility Vehicles
Specifications
Tank |
|
Material |
Blow-molded yellow polyethylene plastic |
Lid |
12.7-cm (5-in.) plastic screw-on breathable lid with tether |
Fill-level indication |
Molded on tank (in gallons) |
Recirculation |
Yes - through tank |
Sump |
Yes - molded in bottom of tank |
Drain |
No drain |
Pump |
|
Type |
Shurflo on-demand diaphragm-type pump |
Pressure |
0 to 4.1 bar (0 to 60 psi) – adjustable through recirculation |
Flow rate |
20 L/min (5.3 gpm) |
Electrical |
18 amps max |
Boom |
|
Material |
Powder-coated steel |
Type |
Manually-folded, spring-loaded breakaway boom |
Nozzles |
XRC TeeJet nozzles with check valve screens |
–Folded width |
1.5 m (5 ft) |
–Unfolded width |
3 m (10 ft) |
Spray width |
3.8 m (12.5 ft) |
Hand wand |
|
Material |
Polypropylene with Viton® rubber seals |
Tip |
Brass - adjustable (mist, cone, stream) |
Hose diameter |
1.3 cm (1/2 in.) |
Hose length |
9.1 m (30 ft) |
Vertical spray distribution |
9.1 m (30 ft) |
Horizontal spray distribution |
10.7 m (35 ft) |
Frame |
|
Material |
Powder-coated steel |
Capacities |
|
Tank capacity |
341 L (90 gal.) |
Weight - tank empty |
65 kg (143 lb) |
Weight - tank full |
380 kg (839 lb) |
Warranty |
|
Residential |
2 years |
Commercial |
6 months |
Components included
- 341-L (90-gal.) sprayer assembly
- 3.8-m (12.5-ft) boom and support components
- 9.1-m (30-ft) deluxe hand wand
- Controller and mounting plate
- 8.1-cm (3.2-in.) display
- Display mounting bracket
- Dash, chassis, and sprayer harnesses
- Hardware
- Operator's manual
Required John Deere parts
- E-Spec Full-Size Crossover Gator Utility Vehicles (XUV835E and XUV865E)
- Dash port attachment harness (BM26268)
- E-Spec attachment harness (BM26266)
- CAN bridge (BUC10316)
- M-Spec Full-Size Crossover Gator Utility Vehicles (XUV835M and XUV865M)
- Dash port attachment harness (BM26268)
- CAN bridge (BUC10316)
- R-Spec Full-Size Crossover Gator Utility Vehicles (XUV835R and XUV865R)
- Dash port attachment harness (BM26268)
- CAN bridge (BUC10316)
- Shurflo is a trademark of Pentair Flow Technologies, LLC. TeeJee is a trademark of Spraying Systems Co. Viton is a trademark of The Chemours Company FC, LLC.
Sprayer wiring kit components
Overview
This sprayer wiring kit provides plug-and-go functionality for customers with Full-Size Crossover Gator Utility Vehicles with deluxe cargo boxes and compatible sprayers. Instead of connecting a sprayer's wiring directly to the battery, this kit utilizes the vehicle's pre-installed wiring for a cleaner initial installation and simplified routine attachment afterwards.
Benefits
- Plug-and-go compatibility utilizing the vehicle's pre-installed wiring instead of connecting directly to the battery
- Convenient dash-mounted switch puts on/off control of a sprayer within short reach
Additional details
Included with each kit are four harnesses. Two (the upper and lower harnesses) are for the on/off rocker switch, which can be installed in one of the blank switch plates on the vehicle's dash. The chassis harness runs along the rear of the chassis, extending power and data ports to the back corner of the vehicle. Lastly, the sprayer harness connects to the chassis harness and runs to the sprayer pump, providing a clean and tidy wiring solution.
Compatibility
- Model year 2018 and newer Gator XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Full-Size Crossover Utility Vehicles
- Sprayers:
- LP33597 – 94.6-L (25-gal.) sprayer for Gator utility vehicles
- LP20852 – 170.3-L (45-gal.) sprayer for Gator utility vehicles
- LP22908 – 170.3-L (45-gal.) deluxe sprayer for Gator utility vehicles
- LP48006 – 341-L (90-gal.) deluxe sprayer for Gator utility vehicles
- LP20853 – 341-L (90-gal.) dual-tank sprayer for Gator utility vehicles
- LP22909 – 341-L (90-gal.) deluxe dual-tank sprayer for Gator utility vehicles
Components included
- Upper dash harness
- Lower dash harness
- Rocker switch (on/off)
- Rocker switch sticker
- Chassis harness
- Sprayer harness
- Hardware (includes zip ties and wire harness clips)
- Installation instructions
Required John Deere parts
- E-Spec Full-Size Gator Utility Vehicles (XUV835E and XUV865E)
- Dash port attachment harness (BM26268)
- E-Spec attachment harness (BM26266)
- M-Spec Full-Size Gator Utility Vehicles (XUV835M and XUV865M)
- Dash port attachment harness (BM26268)
- R-Spec Full-Size Gator Utility Vehicles (XUV835R and XUV865R)
- Dash port attachment harness (BM26268)
Spreaders
0.3-m3 (10-cu ft) in-bed spreader for XUV835 and XUV865
Overview
The 0.3-m3 (10-cu ft) in-bed spreader easily expands the capabilities and productivity of operators with Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles. Featuring exclusive controls and ample hopper capacity, these spreaders are the ideal spreading solution to help operators quickly apply large amounts of ice melt materials.
Benefits
- Easily control the mounted spreader with the 9-cm (3.5-in.) weatherproof, color display. Four push buttons are used to navigate functions including independent adjustment of the auger and spinner speeds, vibratory motor settings, auger reverse to clear out jammed material, and unload mode to completely empty the hopper. The display easily mounts to the vehicle's dash by utilizing existing holes.
- If a controller area network (CAN) bridge (BUC10316) is installed on the utility vehicle, operators can access automatic stop, which halts spreader operation when the vehicle stops moving.
- Enjoy long periods of spreading ice melt materials with the ample volume of the 0.3-m3 (10-cu ft) poly hopper.
- The 7.6-cm (3-in.) diameter steel auger is powered by a direct-drive motor and features variable speed control, automatic jam clearing, and reverse to clear jammed material.
- Quickly cover large areas up to 9.1-m (30-ft) wide using the 30.5-cm (12-in.) diameter steel spinner with independent speed control.
- This entire assembly can be quickly disconnected to access the vehicle's hitch and reduce the spreader's overall footprint for storage.
- Eliminate bridged material inside the hopper with the vibratory motor that features four modes (pulse, low, high, and ramp).
- A top screen and fitted tarp are included to help with material handling. The top screen prevents clumped material from entering the hopper, while the fitted tarp helps keep material dry.
- Get a dedicated, secure fit to the cargo box from the provided mounting hardware. Two stainless-steel tie-down rods secure the spreader to the tie-down hooks in the bed.
Additional details
The 0.3-m3 (10-cu ft) in-bed spread is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.
| Specifications | |
| Measurements | |
| Length - overall | 183 cm (72 in.) |
| Length - spinner removed | 154 cm (60.5 in.) |
| Width | 123.2 cm (48.5 in.) |
| Height - bottom of spinner to top of hopper | 105 cm (41.4 in.) |
| Height - bottom of spreader to top of hopper | 67 cm (26.4 in.) |
| Auger diameter | 7.6 cm (3 in.) |
| Spinner diameter | 30.5 cm (12 in.) |
| Capacities | |
| Hopper volume - filled to top screen | 0.3 m3 (10 cu ft) |
| Spreader weight - hopper empty | 138 kg (305 lb) |
| Spreader weight - hopper full | Varies by material – consult the operator's manual for weight limits |
| Materials | |
| Hopper | Single-piece polyethylene |
| Spinner and frame | Powder-coated steel |
| Top screen | 7.9-mm (5/16-in.) powder-coated steel rod |
| Motors - auger, spinner, vibrator | 12-V, semi-sealed |
| Operation | |
| Maximum spreading width | 9.1 m (30 ft) |
| Display functions |
|
| Warranty | |
| Residential | 1 year |
| Commercial | 6 months |
17AT Cart
-
0.5-m 3 (17-cu ft) capacity
-
453.6-kg (1000-lb) load limit
-
Copolymer polypropylene is compression molded for optimum thickness in all areas and maximum durability
-
Heavy-duty, reinforced structural frame with a 25.4-mm (1-in.) diameter, one-piece axle to handle weight, speed, and bumps
-
Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
-
Double-sealed, high-speed roller bearings to handle a 48-km/h (30-mph) maximum speed
-
Heavy-duty polyethylene bed
-
Accepts dividers to separate cargo (template included)
-
-
All-terrain knobby tires
-
Provides good flotation and traction in mud, sand, and other wet or soft areas
-
Flexes over bumps and ruts for a smoother, more controlled ride
-
Minimizes ground compaction to save turf and prevent ruts in soft ground
-
-
Poly fenders to keep the operator, cart, and vehicle clean
-
Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1.875-in.) ball hitch, including Gator™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
-
Quality and styling compatible with other John Deere equipment
Ordering information
Contact your local John Deere dealer for availability and pricing information.
17AT Cart
Order number: LPPCT17ATJD
0.14-m3 (5-cu ft) drop spreader
Overview
Whether it's a snow removal contractor, a grounds crew at a college campus, or a municipality working downtown, a drop spreader is a professional's choice for precision spreading. This drop spreader combines a large, 0.14-m3 (5-cu ft) material capacity with a precise 109-cm (43-in.) spread width that's ideal for salting sidewalks. Heavy-gauge stainless-steel construction, simple drives, and an industry-exclusive removable rotor tray make this attachment the ultimate spreading solution.
Benefits
- Enjoy long periods of spreading with the stainless-steel hopper that offers 0.14-m3 (5-cu ft) of material capacity.
- The stainless-steel rotor is segmented to enhance the accuracy of material distribution with the 109-cm (43-in.) spread width.
- Simple, enclosed drives help enhance the spreader's longevity.
- Get perfect, tool-free selection of material flow with a six-position gate.
- Experience an easy, tool-free cleanout from the industry-exclusive removable rotary tray.
- Eliminate material bridging with the vibration motor.
- Enhance productivity with the multipurpose use of the spreader. Use it in the winter to spread ice-melt material and in the summer to apply fertilizer, topsoil, and lime.
Additional details
The 0.14-m3 (5-cu ft) drop spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.
To adapt this spreader to a XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.
Specifications:
- Hopper capacity: 159 kg (350 lb), varies by material
- Rotor speed: 1.3 to 6 rpm
- Electrical: 12 V
0.085-m3 (3-cu ft) fertilizer spreader
Overview
The 0.085-m3 (3-cu ft) fertilizer spreader for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles is ideal for applying fertilizer, seed, herbicide, and other fine-particle materials. This spreader features a poly hopper with up to 109 kg (240 lb) of material capacity to minimize refilling. After pairing with a Gator hitch and display (LP69908), spread-width adjustments can be made up to 6.1 m (20 ft).
Benefits
- Enjoy long periods of spreading with a poly hopper that offers 109 kg (240 lb) of material capacity.
- Get long-term durability from the stainless-steel, 25.4-cm (10-in.) diameter spinner.
- Control the flow of fine materials through the adjustable gate operated with an electric actuator.
- Control the spread pattern with the side deflector.
- Satisfy heavy-duty spreading demands using the 1/4-kW (1/3-hp), semi-sealed electric motor.
- Improve durability in rugged conditions with a powder-coated steel frame.
Additional details
The 0.085-m3 (3-cu ft) fertilizer spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.
To adapt this fertilizer spreader to an XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.
0.085-m3 (3-cu ft) salt spreader
Overview
The 0.085-m3 (3-cu ft) salt spreader for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles is the convenient spreading solution for applying rock salt in winter weather. This spreader features a poly hopper with up to 109 kg (240 lb) of material-carrying capacity. After pairing with a Gator hitch and display (LP69908), spread-width adjustments can be made up to 7.6 m (25 ft) wide.
Benefits
- Enjoy long periods of spreading with the poly hopper that offers 109 kg (240 lb) of material capacity.
- Easily move large-particle material, like rock salt, to the spinner with the vertical auger.
- NOTE: The spreader is not well suited to handle fine-particle materials like calcium chloride.
- The 25.4-cm (10-in.) diameter, nylon, glass-reinforced spinner withstands corrosive ice melt products for long-term use.
- Satisfy heavy-duty spreading demands with the 1/4-kW (1/3-hp), semi-sealed electric motor.
- Improve durability in rugged conditions with a powder-coated steel frame.
Additional details
The 0.085-m3 (3-cu ft) salt spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.
To adapt this salt spreader to an XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.
Hitch and display for XUV835 and XUV865
Overview
The hitch and display for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles are specifically designed to work with a 0.085-m3 (3-cu ft) salt spreader (LP69909), a 0.085-m3 (3-cu ft) fertilizer spreader (LP69910), or a 0.14-m3 (5-cu ft) drop spreader (LP69911).
Each hitch features a spring-loaded mechanism to allow for quick spreader attachment and removal. The hitch can also be lowered to provide easy access for routine service.
This latest generation of utility vehicles offer greater electronic capabilities than ever before. As a result, operators have access to enhanced functionality and controls, which is seen through the 9-cm (3.5-in.) weatherproof, color display.
Benefits
- Easily control the mounted spreader with the 9-cm (3.5-in.) weatherproof color display. Four push buttons are used to navigate functions including independent adjustment of the auger and spinner speeds and activating the vibratory motor on 0.14-m3 (5-cu ft) drop spreaders. The display mounts easily to the vehicle's dash by utilizing existing holes.
- If a controller area network (CAN) bridge (BUC10316) is installed on the Gator, operators will also have access to automatic stop functionality, where spreader operation halts when the vehicle stops.
- Designed specifically for Gator utility vehicles, the hitch ensures safe and secure spreader fitment.
- The powder-coated steel hitch provides the utmost support and durability.
Additional details
The hitch and display are compatible with the following models:
- Model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R
- 0.085-m3 (3-cu ft) salt spreader (LP69909)
- 0.085-m3 (3-cu ft) fertilizer spreader (LP69910)
- 0.14-m3 (5-cu ft) drop spreader (LP69911)
Storage
MOLLE large storage pouch - black
MOLLE large storage pouch - camo
MOLLE large storage pouch - brown
NOTE: Available through OrderZone.
The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Dual military-grade zippers and pulls
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 127-mm (5-in.) MOLLE sticks included
- Available in black, brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Built-in drain hole
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
MOLLE device pouch
Available through OrderZone
Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel
Special features:
- Velcro flap closure
- Padded to protect device and contents
- Constructed with military-grade Cordura™ fabrics
- Utilizes the MOLLE attachment system
- Pair of 6-in. (152.4-mm) MOLLE sticks included
- Available in black or REALTREE HARDWOODS HD™ pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Built-in drain hole
- Limited 1-year warranty
- Made In U.S.A.
Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.
MOLLE device pouch
Available through OrderZone
Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel
Special features:
- Velcro flap closure
- Padded to protect device and contents
- Constructed with military-grade Cordura™ fabrics
- Utilizes the MOLLE attachment system
- Pair of 6-in. (152.4-mm) MOLLE sticks included
- Available in black or REALTREE HARDWOODS HD™ pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Built-in drain hole
- Limited 1-year warranty
- Made In U.S.A.
Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.
MOLLE fire extinguisher pouch - black
MOLLE fire extinguisher pouch - camo
MOLLE fire extinguisher pouch - coyote brown
NOTE: Available through OrderZone.
The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Military-grade rapid extraction clips
- Fits standard round 1.1-kg (2.5-lb) fire extinguishers
- Padded to protect contents
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 15.2-cm (6-in.) MOLLE sticks included
- Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
MOLLE fire extinguisher pouch - black
MOLLE fire extinguisher pouch - camo
MOLLE fire extinguisher pouch - coyote brown
NOTE: Available through OrderZone.
The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Military-grade rapid extraction clips
- Fits standard round 1.1-kg (2.5-lb) fire extinguishers
- Padded to protect contents
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 15.2-cm (6-in.) MOLLE sticks included
- Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
MOLLE large storage pouch - black
MOLLE large storage pouch - camo
MOLLE large storage pouch - brown
NOTE: Available through OrderZone.
The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Dual military-grade zippers and pulls
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 127-mm (5-in.) MOLLE sticks included
- Available in black, brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Built-in drain hole
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
MOLLE large storage pouch - black
MOLLE large storage pouch - camo
MOLLE large storage pouch - brown
NOTE: Available through OrderZone.
The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Dual military-grade zippers and pulls
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 127-mm (5-in.) MOLLE sticks included
- Available in black, brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Built-in drain hole
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
MOLLE small storage pouch - black
MOLLE small storage pouch - camo
MOLLE small storage pouch - brown
NOTE: Available through OrderZone.
The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Military-grade zippers and pulls
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 127-mm (5-in.) MOLLE sticks included
- Available in black, brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Limited 1-year warranty
- Made in the USA
Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
MOLLE small storage pouch - black
MOLLE small storage pouch - camo
MOLLE small storage pouch - brown
NOTE: Available through OrderZone.
The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Military-grade zippers and pulls
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 127-mm (5-in.) MOLLE sticks included
- Available in black, brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Limited 1-year warranty
- Made in the USA
Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
Water bottle pouch with three color options
Overview
This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.
Benefits
- Military-grade zipper and pull
- Constructed with military-grade CORDURA® fabrics
- Easily attaches with built-in straps
- Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
- Durable inner liner made of high-density coated pack cloth nylon fabric
Additional details
- Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.
MOLLE fire extinguisher pouch - black
MOLLE fire extinguisher pouch - camo
MOLLE fire extinguisher pouch - coyote brown
NOTE: Available through OrderZone.
The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Military-grade rapid extraction clips
- Fits standard round 1.1-kg (2.5-lb) fire extinguishers
- Padded to protect contents
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 15.2-cm (6-in.) MOLLE sticks included
- Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
Water bottle pouch with three color options
Overview
This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.
Benefits
- Military-grade zipper and pull
- Constructed with military-grade CORDURA® fabrics
- Easily attaches with built-in straps
- Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
- Durable inner liner made of high-density coated pack cloth nylon fabric
Additional details
- Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.
Water bottle pouch with three color options
Overview
This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.
Benefits
- Military-grade zipper and pull
- Constructed with military-grade CORDURA® fabrics
- Easily attaches with built-in straps
- Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
- Durable inner liner made of high-density coated pack cloth nylon fabric
Additional details
- Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
- Limited 1-year warranty
- Made in the USA
CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.
Rapid recovery rope kit
Available through OrderZone
Special features:
- Extreme off-road kinetic recovery rope and storage bag
- Rope measures 9/16 in. (21 mm) X 20 ft (6.1 m) and is constructed of double-braided nylon
- 5,000-lb (2268-kg) tensile strength
- Bag is constructed with military-grade Cordura™ fabrics with built-in carry handle
- Bag utilizes the modular lightweight load-carrying equipment (MOLLE) attachment system with two 6–in. (152.7-mm) MOLLE sticks included
- Bag available in black or REALTREE HARDWOODS HD™ pattern
- Limited 1-year warranty
- Made In U.S.A.
Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.
Rapid recovery rope kit
Available through OrderZone
Special features:
- Extreme off-road kinetic recovery rope and storage bag
- Rope measures 9/16 in. (21 mm) X 20 ft (6.1 m) and is constructed of double-braided nylon
- 5,000-lb (2268-kg) tensile strength
- Bag is constructed with military-grade Cordura™ fabrics with built-in carry handle
- Bag utilizes the modular lightweight load-carrying equipment (MOLLE) attachment system with two 6–in. (152.4-mm) MOLLE sticks included
- Bag available in black or REALTREE HARDWOODS HD™ pattern
- Limited 1-year warranty
- Made In U.S.A.
Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.
Side-door opening toolbox
This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.
Side-door opening toolbox features:
- 125-L (4.4-cu ft) sealed storage
- Heavy-gauge sheet metal
- D-rings for tie downs
- Fully sealed lockable latch
- Sealed door
- Door can also be used as a work bench when down
- Can be mounted on either side of the cargo box
Weight |
29 kg (64 lb) |
Capacity |
34 kg (75 lb) |
Dimensions |
Full box: 109.4-cm (43.1-in.) long, 35-cm (13.8–in.) wide, and 32.5-cm (12.8–in.) tall |
The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate and bolting the toolbox onto the cargo box.
The toolbox requires the tailgate with brake and tail lights kit (BUC10393) and optional label kit:
- BM26220 – green and yellow
This toolbox is compatible with the following Gator™ Utility Vehicle models:
- TX
- TX Turf
- TE
- TH
- XUV625i
- XUV825i/E/M
- XUV825i/E/M S4
- XUV855D/E/M
- XUV855D/E/M S4
- XUV835E/M/R
- XUV865E/M/R
- Model year 2018 and newer HPX615 and HPX815
MOLLE small storage pouch - black
MOLLE small storage pouch - camo
MOLLE small storage pouch - brown
NOTE: Available through OrderZone.
The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.
Special features:
- Military-grade zippers and pulls
- Constructed with military-grade CORDURA® fabrics
- Utilizes the MOLLE attachment system
- Pair of 127-mm (5-in.) MOLLE sticks included
- Available in black, brown, or Realtree Hardwoods HD® camo pattern
- Inner liner made of high-density coated pack-cloth nylon fabric
- Limited 1-year warranty
- Made in the USA
Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.
Tailgate with brake lights and taillights
This tailgate kit with brake lights and taillights is specifically designed for compatibility with the top and side-door toolboxes (BM26162 and BM26160).
The tailgate can be installed in minutes once the toolbox and tail lights are installed by bolting them to the tailgate bracket.
Optional label kits are designed to fit with this tailgate:
- BM26220 – green and yellow
The tailgate is compatible with the following Gator™ utility vehicle models:
- TX
- TX Turf
- TE
- TH
- XUV625i
- XUV825i/E/M
- XUV825i/E/M S4
- XUV855D/E/M
- XUV855D/E/M S4
- XUV835E/M/R
- XUV865E/M/R
- Model Year 2018 - current HPX615 and HPX815
Top-door opening toolbox
This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.
Top door opening toolbox features:
- 125-L (33-gal.) sealed storage
- Heavy-gauge sheet metal
- D-rings for tie downs
- Fully sealed lockable latch
- Sealed door
- Toolbox divider
- Removable tool tray
- Can be mounted on either side of the cargo box
|
Top door opening toolbox |
Toolbox weight |
32.7 kg (72 lb) |
Toolbox capacity |
32.7 kg (75 lb) |
Toolbox dimensions |
-Tray: 27.4-cm (10.8-in.) long x 21.8-cm (8.6-in.) wide x 7.1-cm (2.8–in.) deep -Left-hand side compartment: 46.2-cm (18.2–in.) long X 32.5-cm (12.8–in.) wide X 35.3-cm (13.9–in.) tall -Right-hand side compartment: 62.7-cm (24.7–in.) long X 32.5-cm (12.8–in.) wide X 35.3-cm (13.9-in.) tall -125-L (33-gal.) total volume |
The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.
The toolbox requires the tailgate with brake and tail lights kit BUC10393 and optional label kit:
- BM26220 – green and yellow
This toolbox is compatible with the following Gator™ Utility Vehicle models:
- TX
- TX Turf
- TE
- TH
- XUV625i
- XUV825i/E/M
- XUV825i/E/M S4
- XUV855D/E/M
- XUV855D/E/M S4
- XUV835E/M/R
- XUV865E/M/R
- Model year 2018 and newer HPX615 and HPX815
Winch
Winch accessories kit
Double the pulling power, change the pulling direction, and keep the winch in proper working order.
The accessories kit is essential gear for operators getting the most out of their winch:
-
Effectively anchors to trees/boulders
-
Change the pulling direction
-
Double the pulling capacity
The accessories kit includes:
-
Flexible tree strap
-
Snatch block
-
Shackle
Each kit comes in a black Cordura® heavyweight-nylon soft case.
Cordura is a trademark of INVISTA.
2041-kg (4500-lb) winch (chassis mounted)
Plug-in remote
Key features
- Impressive pulling capacity of 2041 kg (4500-lb)
- Equipped with a water-resistant contactor that supplies the amperage required for higher pulling capacities
- Includes a 3.05-m (10-ft), water-resistant, plug-in remote for safe distance operation that plugs directly into the glove box
- 15.2 m (50 ft) of 5.6-mm (7/32-in.) synthetic rope with hawse fairlead
- Synthetic rope does not develop sharp burrs like steel rope and does not store as much potential energy when under load
- Ergonomic clutch handle
- Limited lifetime, 3-year electrical (North America) warranty offered through WARN
Compatibility
- Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
- M-spec and R-spec vehicles come from the factory winch ready, and no additional attachment harnesses are required
- Requires winch mounting kit to mount the winch either on the chassis or on the front or rear receiver
- Not compatible with winch mounts BM26252 and BM26393
Electrical harness requirements
| XUV835/865 | Attachment harness required (see below) |
| E | 1 |
| 1 | E-spec attachment harness |
| 2 | Front attachment harness |
| 3 | Roof attachments harness |
| 4 | Front cab harness |
| 5 | Rear cab harness |
| 6 | Dash port harness |
WARN is a trademark of WARN Industries, Inc.
Wireless winch remote
Wireless winch remote mounted on XUV835
Key features
- Wirelessly control winch from up to 15 m (50 ft) away
- Weatherproof transmitter has two large buttons, making it easy to operate even while wearing gloves
- Colored light-emitting diode (LED) lights provide clear operator feedback
- Kit includes wireless transmitter, receiver, holster, wiring, and mounting hardware
Compatibility
- Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
- Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
- Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Reviews
Location: Hermann mo
Length of Ownership: 6months
Usage: Daily
Fourth gator that I have owned Needs shifter improved plus parking break
Location: Scottsburg, Indiana
Length of Ownership: 3months
Usage: Daily
I have had several gators and to tell the truth I am a big JD fan right out of the gate. I have been on the fence for several years about purchasing a newer gator and been looking at used ones. 48 months zero interest we thought why not. Got it just before thanksgiving and we just love it. Drove it all over town, helps the wife take in groceries and I get a new toy to deck out.
Location: North Dakota
Length of Ownership: 1yearOrLonger
Usage: Daily
The power steering stops quite often. I then need to stop the engine, restart, and then it goes as long as it wants to, but then kicks out again. My dealer can't seem to find out why.
Videos
In 1953, Wyatt (JR) Smith bought Smith Tractor Company. Smith originally purchased a Ford tractor dealership until the company took on John Deere products in January of 1987. Since then, Smith Tractor Company has proudly provided John Deere equipment and service throughout Florida & Alabama. Our customer base is built on relationships and in today’s corporate world that is a rare commodity. You will find quite a bit of inventory if you take a trip to one of our locations.
Frisco City, AL
3854 Bowden St.
Frisco City, AL 36445
Phone 251-267-2500
Toll Free 800-221-4052 Option 3
Directions
Atmore, AL
8974 Hwy 31
Atmore, AL 36502
Phone 251-368-1720
Toll Free 800-221-4052 Option 2
Directions
Jay, FL
3834 Highway 4
Jay, FL 32565
Phone 850-675-4505
Toll Free 800-221-4052 Option 1
Directions
© COPYRIGHT 2024 SMITH TRACTOR CO. EQUIPMENT - ALL RIGHTS RESERVED| Privacy Policy | Powered By